low signal relay g5v-2 63 low signal relay g5v-2 miniature relay for signal circuits ? suitable for handling low signals in computer peripherals, telecommunications and security equipment. ? capable of switching loads 10 a to 2 a. ? conforms to fcc part 68 1,500 v surge withstand. ? reliable ag + au-clad, bifurcated crossbar contacts. ? fully-sealed construction. ? rohs compliant. r c fcc ordering information to order: select the part number and add the desired coil voltage rating (e.g., g5v-2- dc12 ). model number legend specifications contact data note: p level: 60 = 0.1 x 10 ?6 /operation this value was measured at a switching frequency of 120 oper ations/min and the criterion of contact resistance is 50 . this value may vary depending on the switching frequency and operating environment. al ways double-check relay suitability under actual operating co nditions. type contact form construction model standard dpdt fully-sealed g5v-2 high-sensitivity g5v-2-h1 1. contact form 2: dpdt 2. coil type blank: standard h1: high-sensiti v ity 3. rated coil volta g e 3, 5, 6, 9, 12, 24, 4 8 v dc g5v - - dc 1 3 2 item standard high-sensitivity load resistive load (p.f. = 1) rated load 0.50 a at 125 vac 2 a at 30 vdc 0.5 a at 125 vac 1 a at 24 vdc contact material ag (au clad) carry current 2 a max. operating voltage 125 vac 125 vdc max. operating current 2 a 1 a max. switching capacity 62.5 va 60w 62.5 va 24w min. permissible load (see note) 10 a, 10 mvdc
64 low signal relay g5v-2 coil data standard type high-sensitivity type note: 1. the rated current and coil resistance ar e measured at a coil temperature of 23 c with a tolerance of 10%. 2. the operating characteristics are m easured at a coil temperature of 23 c. 3. the maximum voltage is the highest voltage that can be imposed on the relay coil. characteristics note: 1. the contact resistance was me asured with 10 ma at 1 vdc with a fall-of-potential method. 2. values in parentheses are typical values unless otherwise stated. 3. the insulation resistance was measured with a 500-vdc megohmmeter applied to the same parts as those for checking the dielectri c strength. 4. the above values are initial values. rated voltage (vdc) rated current (ma) coil resistance ( ) coil inductance (ref. value) (h) pick-up voltage dropout voltage maximum voltage power consumption (mw) armature off armature on % of rated voltage 3 166.70 18 0.04 0.05 75% max. 5% min. 120% max. at 23 c approx. 500 5 100 50 0.09 0.11 6 83.30 72 0.16 0.19 9 55.60 162 0.31 0.49 12 41.70 288 0.47 0.74 24 20.80 1,152 1.98 2.63 48 12 4,000 7.23 10.00 approx. 580 rated voltage (vdc) rated current (ma) coil resistance ( ) coil inductance (ref. value) (h) pick-up voltage dropout voltage maximum voltage power consumption (mw) armature off armature on % of rated voltage 3 50 60 0.18 0.57 75% max. 5% min. 180% max. at 23 c approx. 150 5 30 166.7 0.46 0.71 6 25 240 0.70 0.97 9 16.70 540 1.67 2.33 12 12.50 960 2.90 3.99 24 8.33 2,880 6.72 9.27 approx. 200 48 6.25 7,680 20.10 26.70 150% max. at 23 c approx. 300 contact resistance (see note 1) 50 m max. (g5v-2); 100 m max. (g5v-2-h1) operate time (see note 2) 7 ms max. (mean value: approx. 3.5 ms) release time (see note 2) 3 ms max. (mean value: approx. 0.8 ms) operating frequency (max.) mechanical 36,000 operations/hour electrical 1,800 operations/hour (under rated load) insulation resistance (see note 3) 1,000 m min (at 500 vdc) dielectric strength 1,000 vac, 50/60 hz for 1 minute between coil and contacts 1,000 vac, 50/60 hz for 1 minute between contacts of different poles 750 vac, 50/60 hz for 1 minute between contacts of same poles (500 vac, 50/60 hz for 1 minute between cont acts of same poles for high-sensitive type) surge withstand voltage 1,500 v (10 x 160 s) between coil and contacts (conforms to part 68 of fcc rules) vibration mechanical durability 10 to 55 hz, 1.50 mm double amplitude malfunction durability shock mechanical durability 1,000 m/s 2 (approx. 100 g) malfunction durability 200 m/s 2 (approx. 20 g), 100 m/s 2 (approx. 10 g) fo r high-sensitive type ambient temperature operating/storage -25 to 70 c (?-h1? versions) with no icing -25 to 65 c (standard versions) with no icing humidity 5% to 85% rh service life mechanical 15 million operations min. (at operating frequency of 36,000 operations/hour) electrical 100,000 operations min. (at 1,800 operations/hr), standard models. see ?characteristic data? weight approx. 5 g
low signal relay g5v-2 65 characteristic data g5v-2 g5v-2-h1 maximum switchin g capacity ambient temperature vs. maximum coil volta g e electrical service life rated operating c u rrent (a) rated operating v oltage ( v ) rated operating c u rrent (a) ser v ice life (x10 operations) 3 am b ient temperat u re ( ) maxim u m coil v oltage ( % ) coil rated v oltage 3 to 24 v dc 4 8 v dc 30- v dc resisti v e load 125- v ac resisti v e load 123 ac resisti v e load dc resisti v e load note: the maxim u m coil v oltage refers to the maxim u m v al u e in a v arying range of operating po w er v oltage, not a contin u o u s v oltage. maximum switchin g capacity ambient temperature vs. maximum coil volta g e electrical service life rated operating c u rrent (a) rated operating v oltage ( v ) rated operating c u rrent (a) ser v ice life (x10 operations) 3 am b ient temperat u re ( ) maxim u m coil v oltage ( % ) ac resisti v e load dc resisti v e load 5 3 1 0.7 0.5 0.3 0.2 0.1 0 24- v dc resisti v e load 125- v ac resisti v e load 1000 500 300 100 50 30 10 3 to 24 v dc 4 8 v dc 200 1 8 0 160 140 120 100 8 0 0 note: the maxim u m coil v oltage refers to the maxim u m v al u e in a v arying range of operating po w er v oltage, not a contin u o u s v oltage.
66 low signal relay g5v-2 dimensions note: 1. all units are in millimeters unless otherwise indicated. 2. tolerance: 0.1 3. orientation marks are indicated as follows: g5v-2, g5v-2-h1 approvals ul recognized (file no. e415 15) / csa certified (file no. lr31928) - - ambient temp. = 40 c note: 1. the rated values approved by each of the safety standards may be different from the performance characteristics individually de fined in this catalog. 2. in the interest of product improvement, specifications are subject to change. precautions long-term continuously on contacts using the relay in a circuit wher e the relay will be on continuously for long periods (without switching) can lead to unstable contacts because the heat generated by the coil itself will affect the insulation, causing a film to develop on the contact surfaces. be sure to use a fail-safe circuit design that provides protecti on against contact failure or coil burnout. relay handling when washing the product after soldering the relay to a pcb, use a water-based solvent or alcohol-based solvent, and keep the solvent temperature to less than 40 c. do not put the relay in a cold clean- ing bath immediately after soldering. type contact form coil rating contact ratings g5v-2 dpdt 3 to 48 vdc 0.6 a at 125 vac (general use) 0.6 a at 110 vdc (resistive) 2 a at 30 vdc (resistive) g5v-2-h1 3 to 48 vdc 0.5 a at 125 vac (general use) 0.2 a at 110 vdc (resistive) 1 a at 24 vdc (resistive) terminal arrangement/ internal connections (bottom view) mounting holes (bottom view) tolerance: 0.1 20.5 max. 20.3 typ. 10.1 max. 9.9 typ. 11.5 max. 11.4 typ. 0.5 3.5 7.62 0.3 0.5 7.62 5.08 5.08 (1.3) 7.62 (1.3) eight, 1-dia. holes (1.2) 1 16 4 13 6 11 8 9
low signal relay g5v-2 memo
low signal relay g5v-2 omron on-line global - http://www.omron.com usa - http://www.components.omron.com cat. no. x301-e-1b printed in usa omron electronic components llc 55 e. commerce drive, suite b schaumburg, il 60173 847-882-2288 09/11 specificat ions subject to change without notice all sales are subject to omron electronic components llc standard terms and conditions of sale, which can be found at http://www.components.omron.com/compon ents/web/webfiles.ns f/sales_terms.html all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.0393 7. to convert grams into ounces, multiply by 0.03527.
|
